PRODUCTS- 產品介紹 -

WISE-7555M

WISE-7555M
WISE-7555M
WISE-7555M

產品型錄(PDF)

操作手冊(PDF)
 

產品介紹

WISE (Web Inside, Smart Engine) 為泓格科技所開發；具備自主邏輯控制與遠端監控通知等多項功能的智慧型控制器。在此系統下，使用者不再困擾於控制器中邏輯程式的撰寫，而僅需透過 WISE 所提供的網頁人機介面及滑鼠點選動作，即可完成控制器上工作邏輯的規劃，過程簡單且快速，其可大幅降低使用者在系統開發上的資源花費。

WISE-7555M 遵照 IEEE 802.3af 標準 (classification, Class 1) 中的 Power over Ethernet (PoE) 規範，可在PoE網路環境下透過網路線 (Category 5) 傳送電力。此功能提供了更大的靈活性及效率以簡化系統設計、節省空間並減少電線及電源插座的需求。此外，WISE-7555M 內建雙乙太網口 (Two-port Ethernet switch)，不需透過交換機 (Switch) 即可直接進行最多10個模組的串接。讓現場佈線更加方便。

WISE-7555M 提供 8 組 DI 通道及 8 組 DO 通道。透過內建的 IF-THEN-ELSE 邏輯規則執行引擎，WISE-7555M 可提供 I/O 通道監控、計時器/排程時序控制、E-mail/CGI 命令發送等功能，可運用於自動化監控應用中。此外，WISE-7555M 同時支援 Modbus TCP 及 MQTT 通訊協定，可與 SCADA、IoT 系統進行無縫整合。

產品特色

  • 內建網頁伺服器，無須安裝軟體工具
  • 無須撰寫程式，僅需要點選即可完成規則編輯
  • 內建 IF-THEN-ELSE 的邏輯運算引擎
  • 內建 I/O 通道 (8 組 DI 通道及 8 組 DO 通道)
  • 支援 IO 通道監控、計數器、計時器、排程、Email 發送、CGI 命令發送等指令
  • 透過 Modbus TCP 與 SCADA 系統進行無縫整合
  • IEEE 802.3af 標準 Power over Ethernet (PoE)
  • 內建雙乙太網口 (Two-port Ethernet switch)，提供 Daisy-Chain 方式連接
  • 透過 MQTT 協定與 IT 及物聯網 (IoT) 系統進行無縫整合

產品應用

自動化建築、自動化工廠、自動化機械、遠端維護、遠端診斷及測試設備等。

硬體規格

Digital Input/Counter
Channels 8
Contact Dry +Wet
Sink/Source (NPN/PNP) Dry: Source
Wet: Sink/Source
Wet Contact On Voltage Level +10 VDC to +50 VDC
Off Voltage Level +4 VDC Max.
Dry Contact On Voltage Level Close to GND
Off Voltage Level Open 
Input Impedance 10 kΩ
Counters Max. Counts 16-bit (65535)
Max. Input Frequency 50 Hz
Min. Pulse Width 10 ms
Overvoltage Protection +70 VDC
Effective Distance 500 M Max.
Digital Output
Channels 8
Type Isolated Open Collector
Sink/Source (NPN/PNP) Source
Max. Load Current 650 mA/channel at 25°C
Load Voltage +10 VDC to +40 VDC 
Overvoltage Protection 47 VDC
Overload Protection -
Short-circuit Protection Yes
Communication
Ethernet Port 2 x RJ-45, 10/100 Base-TX, Swtich Ports
PoE Yes
Protocol Modbus TCP, MQTT
LED Indicators
for System Running Yes
for Ethernet Link/Act Yes
for I/O Channel Status Yes
for PoE Power Yes 
2-Way Isolation
I/O 2500 VDC
EMS Protection
ESD (IEC 61000-4-2) ±4 kV Contact for Each Terminal and 
±8 kV Air for Random Point
EFT (IEC 61000-4-4) ±2 kV for Power Line
Surge (IEC 61000-4-5) ±2 kV for Power Line
Power
Reverse Polarity Protection Yes
Powered from Terminal Block 12 to 48 VDC
Powered from PoE Yes, IEEE 802.3af, Class1
Consumption 3.7 W (Max.)
Mechanical
Dimensions (L x W x H) 120mm x 97mm x 42mm
Installation Wall mounting
Environment
Operating Temperature -25 °C to +75 °C
Storage Temperature -30 °C to +80 °C
Humidity 10 to 90% RH, non-condensing

軟體規格

Functions
Rule Configuration Website Access Web server on WISE controllers to edit and upload logic rules through web browser.
72 IF-THEN-ELSE Logic Rules 3 IF conditions with AND or OR operators
3 THEN actions and 3 ELSE actions
48 Internal Registers Hold temporary variables and read/write data
24 Timers Delay / Timing functions.
24 Schedules Setup prescheduled routine tasks.
24 Emails Send Email messages to pre-set Email receivers.
24 CGI Commands Send pre-set CGI commands.
24 Recipes Set up THEN/ELSE action groups.
8 P2P remote modules Set up the connection information for the remote WISE modules.
Modbus TCP Protocol Real time control and monitoring I/O channels and system status of controllers via SCADA software.
MQTT Protocol Real time message publish/subscribe mechanism for I/O channels and system status via IT/IoT software.
IF Conditions
DI Channel ON, OFF, ON to OFF, OFF to ON, Change
Internal Register = 、> 、< 、 ≥ 、 ≤ (value)
DI Counter = 、> 、< 、 ≥ 、 ≤ (value), Change
DO Counter
Timer Timeout, Not Timeout
Schedule In Range, Out of Range
P2P DI, AI, DI counter, DO counter, IR
Rule Status Enable, Disable
THEN / ELSE Actions
DO Channel ON, OFF, Pulse Output
Internal Register Change the value
DI Counter Reset
DO Counter
Timer Start, Reset
Schedule Enable, Disable
Email Send
MQTT message
CGI Commands
Recipe Execute
P2P DO(On/Off), AO, IR
Rule Status Enable, Disable
Back List